13306647218

Copper Tube Information

Company dynamics

brass swagelok tube fitting male connector

author:MF manufacturerstime:2022-03-10 18:35:52

one. Shiwei Lockka set design characteristics

brass swagelok tube fitting male connector
(brass swagelok tube fitting male connector)

1. Mechanical seating design of double card sets

Dual card sets will seal the sealing function and the grabbing function of the card holder, Each card set is optimized for its corresponding function.。

The front jacket is used to form a seal:

Seal between the joint body

Card sleeve outer diameter seal

Rotating nut, After the card holder will:

Push the front jacket along the axial direction

Apply an effective card holder to grasp the radial direction

2. Hinge-Rear card set design of the clamp

Excellent gas seal and card sets to grasp

(brass swagelok tube fitting male connector)Easy to perform correct installation

Do not transfer torque to card sleeve when installing

Reliable

Excellent anti-vibration fatigue performance and card holder support

Completely compatible with the same size of the world

two. common1 in/25 mm And the following Shiwukka casing joint installation instructions

1. Complete the card holder into the joint,And inserted into the end。

brass swagelok tube fitting male connector
(brass swagelok tube fitting male connector)


2. Facing the nut with your fingers until,exist6Nod position to give the nut sign。

brass swagelok tube fitting male connector


(brass swagelok tube fitting male connector)3. Fixed joint body,Tighten the nut1Another quarter,Stopped at9Bit clock position(for 1/16, 1/8 and 3/16 in.;2, 3 and 4 mm Card sleeve joint, Only three-quarters of the nuts are stopped 3 Bitter position)。

brass swagelok tube fitting male connector(brass swagelok tube fitting male connector)


three. Exceed1 in./25mm Shiwei Lockka casing joint installation method

1. Using the World Welocco Multi-head hydraulic preloading device(MHSU) Pre-installed the card holder on the card holder。

brass swagelok tube fitting male connector


MHSUPre-installer

2. Lubricants supplied with the joint on the rear surface of the bulk thread and the rear cartridge。

3. Insert the card holder with pre-assembled card sets into the joint, Until the top card set on the joint body,Tighten the nut with hand。

(brass swagelok tube fitting male connector)4. exist 6 The position of the bit is marked to the nut。

5. Keep the joint body, Tighten the nut in one-half of the circle to stop 12 Bitter position。

(brass swagelok tube fitting male connector)Four. Precautions for removal

1. You must first remove the system pressure and then remove the Rockka casing joint.。

(brass swagelok tube fitting male connector)2. Before disassembling, Marking on the back surface of the nut;Draw a line on the plane of the nut and connector body(These tags are used to ensure that the nuts are transferred to the previous fastened position when reputing.)。

brass swagelok tube fitting male connector(brass swagelok tube fitting male connector)


3. Put the card sleeve with pre-assembled card holders into the joint, until the top of the front card is on the joint body。

brass swagelok tube fitting male connector(brass swagelok tube fitting male connector)
(brass swagelok tube fitting male connector)
(brass swagelok tube fitting male connector)


4. Keep the joint body, Use the wrench to transfer the nut to the previous fastening position of the tag indication on the card holder and on the body plane。At this time, You will feel that the resistance is significantly increased(Repeat multiple tube connections,Can rotate more10°~20°)。

brass swagelok tube fitting male connector


Fives. Use of gap detection rules

brass swagelok tube fitting male connector(brass swagelok tube fitting male connector)


1. Can only use the detection of the detection connector in the first installation。

2. Squire the Gap gap detection in the gap between the nut and the body。

3. If the detection specification cannot insert a gap, Then indicate that the joint is fully fastened.。

4. If the detection rule can be inserted into the gap, Then explain it needs to be fastened.。

six. Other considerations

(brass swagelok tube fitting male connector)1. Do not block the system by loosening the joint nut or connector。

2. Do not install or fasten the connector when there is pressure in the system。

3. Make sure that the card sleeve is close to the shoulder of the card sleeve before the fastening nut.。

4. First installation, Use the correct Wen Weido gap detection to ensure full tightness。

(brass swagelok tube fitting male connector)5. Do not mix different materials or joint components produced by different manufacturers——Card holder, card cover, Nuts and connector body。

6. Do not rotate the connector body。And the joint body should be fixed and rotate the nut.。

7. The material of the metal card holder should be soft than the fitting。E.g: Stainless steel card casing must not be used with brass joints。

8. When the card holder and joint are made of the same material, The card holder must be completely annealed。

9. Surface finish is very important for the correct seal。There is any type of recessed,Scratch, Boeing parts or other surface defects will be difficult to seal, Especially in the gas device。

10. Tube must be plugged in when installing。

(brass swagelok tube fitting male connector)11. Two cards can no longer,Can not be reversed before and after。

Random recommendation